"Power Plus Annihilator"
The most powerful heavy duty wood auger
CARBIDE TIPPED
1/2" * 9/16" * *5/8" * 11/16" *3/4" * 13/16" * 7/8" * 15/16" * 1" *
1-1/16" * 1-1/8 * 1-3/16" * 1-1/4 * 1-3/8 *
* 1-1/2 * 1-3/4 *1-5/16" up to 4"diameters.
12"- 18"- 24"- 36"- 48" and up to 144" plus lengths
 
carbide tipped wood auger bits
with hardened spur.
sizes available
EXTRA LONG Carbide Tipped Wood Auger Drill Bits and
Extra Large and Extra Long Wood Augers! Designed with long lasting unique spurred edge design. A bit that requires less power from your drill, leaving smooth hole walls. For further unhindered exit of drill shavings, the bit is additionally threw hardened . There is no better wood auger bit in the trade. We guarantee it. Carbide tipped auger bits are stronger than tri-cut augers. The heavier weight can withstand the rigors on the job, day in, day out.
They are made with attention to engineering and precise manufacturing tolerances. |
Soft or hard woods, fiberglass, composites, heavy green woods, forestry, Home Builders,
Timber Framing, Glue lam, Truss Construction, Treated Woods, Boat Building,
Sea Wall Construction, Underwater Construction, Utility poles, Landscaping,
Wood Bridge Construction. Heavy Equipment, Wood Matt Construction,
and more. No run-out or wandering.
EXTRA LONG
Carbide Tipped Wood Auger Drill Bits
Extra Large and Extra Long Wood Augers.
Clean Entry and Exits!
CAN BE USED WITH
ELECTRIC, AIR ,GAS POWERED DRILL MOTORS.
CAN BE COMPLETELY REBUILT!
Socket, SDS, Spline
and Standard Shanks!
The Power Plus Annihilator
will out-perform all other drills!
7/16", 5/8", Hex Shanks,
3/4 (Round),1, 1-1/4-7 (socket, SDS, or spline)
Custom diameters and lengths
made for your needs.
 
The Annihilators are carbide tipped wood drill bits that have a carbide-tipped
cutting tip combined with a hardened steel cutting edge.
This allows the Annihilator carbide tipped
wood drill bits to bore holes in all types of wood quickly,
leaving little or no residue. A truly clean, smooth hole is produced.
The carbide tipped wood drill bits requires less torque to operate
and can be used with electric, air, or gasoline powered drill motors and impact wrenches. The carbide cutter is brazed onto the steel body and the hardened steel cutting edge
can be sharpened. The lead screw, shank, and carbide cutter are replaceable
allowing thee Annihilator carbide tipped wood drill bits to be completely rebuilt.
Carbide Tip Counter Bore Diameters
7/16 * 5/8 * 3/4 * 1-1/4 * 1-1/2 *
2 * 2-1/2 * 3 * 3-1/2
Hex or round Shanks,
1/2, 5/8, 3/4, (Round), (socket, SDS, or spline)
special custom sizes made for your applications!
  
4-1/2 Diameter
custom carbide counter sink
(below)
 
"Marine Shark bits"
Call for price.
hand brace bits / wood ship auger / pole bits
electricians bits / utility bits
Standard High Speed Steel
All styles of augers.
Single spur, double spur, bare foot and more,
available in all sizes and lengths.
Call us for pricing and availability.
7 pc. Auger Bit Set, 6 1/2"length 5/8",3/4",7/8",1",1 1/8",1 1/4",1 3/8"
7 pc. Auger Bit Set, 9" long 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1"
7 pc. Auger Bit Set, 18" long. 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1" Individual augers from 3/8 to 2"
Turf Drills
For golf courses, sports stadiums, landscaping.
specially manufactured for each need.
Marine
( under water):
Coring and drilling bits
Ice and Snow drills
 Pneumatic Drill Motors
2" capacity Reversible
LIST-$5889.90
prices cannot be advertised, Call for substantial discount.
- Ideal for drilling wood in marine timbers, underwater use and railroad repair work
- Thrust bearing support for long life and efficient operation
- Lever throttle and durable spur gearing
- Breast plate and dead handle included
- Includes threaded exhaust port
- Use underwater with Air Tool Line Conditioner
|
|
|
|
|
Pneumatic Drill Motors
2" capacity Reversible
prices cannot be advertised, Call for substantial discount.
 | Model ADV-1924 - Variable Speed (speed control dial) | | Capacity in wood: | 2" Diameter | | Reversible: | Yes | | Power: | 3 HP | | Chuck Style: | 1/2" Wood boring | | Spindle: | #2 Morse Taper | | Free Speed: | 700 RPM | | Recommended Hose Size: | 1/2" | | Overall Height: | 18-1/2" | | Weight: | 24-3/4 lbs. | | Air Inlet Thread: | 1/2" ID | | Air Exhaust Thread : | 1/2" NPT | | Air Consumption at 90 PSI : | 50 CFM |
|
Model ADV-1932
with self-closing roll throttle
Up to 3" for boring wood LIST-$7425.60 |
|
|
|
|
|
Model adv- 1932
with self-closing roll throttle
Up to 3" for boring wood |
|
|
|
|
Drill Drives and Power Drives
Model No.'s:
(with Torque Control)
These powerful 16 AMP motors have high torque output. They feature variable speed in two changeable gear ratios.
They are reversible and include a mechanical safety clutch.
Model also includes electronic torque control which can be set at a value that prevents overloading
or over-rolling for tube applications. The motor automatically shuts off at the torque value preset by the operator.
These motors are ideal for many jobs that require portable power drives or drill motors.
Available Accessories include Morse Taper adaptors with a male square drive in sizes 1/2", 3/4" and 1".
|
| "Ultimate Aggressor "
Heavy Duty Wood Auger
CARBIDE TIPPED
Sizes Available
Power wood auger flute design
gives the Ultimate Aggressor the ability
to drill faster than ordinary wood augers.
Quick Change Hex Shank, designed for use with pneumatic, electric and hydraulic drill motors, when drilling wooden railway cross ties, pressure treated lumber, creosote poles, heavy timber, bulkheads, trees, utility poles, decking, glu-lam and more. Double flute design with extended lip double cutters, two outlying spurs, and extreme duty self-feeding screw point for boring clean holes. Milled from one solid piece of 4140 alloy steel. Because of it's rugged construction, The "Ultimate Aggressor's are used by log home builders, arborists, railroad construction, sea wall erectors, maintenance departments, dock builders, utilities, etc...EXTRA LONG Carbide Tipped Wood Auger Drill Bits
Extra Large and Extra Long Wood sizes.
The Ultimate Aggressor wood auger is able to accept
the high torque and high R.P.M.LOADS. loads
generated by today's most powerful
drills and impact wrenches.
9/16" * 11/16" *5/8" * 3/4" * 3/16" * 15/16" * 1" *
1-1/16" * 1-1/8 * 1-3/16" * 1-1/4 * 1-3/8 *
* 1-1/2 * 1-3/4 *1-5/16" up to 4"diameters.
12"- 18"- 24"- 36"- 48" and up to 144" plus lengths*
For treated or green wet lumber.
Boat building, utility pole,
log home construction, sea walls,
bridge const, crane mats, and more.
Shank Construction available for:
Socket, SDS, Splined,
Threaded, Hex, and standard round.
These are truly long lasting, heavy-duty carbide tipped wood auger drills.
Able to accept the high torque load and high R.P.M.LOADS. level
generated by the most powerful impact wrenches and drill motors.
Hydraulic tools like the Stanley ID-04 “Yellow Jacket” impact wrench, Unitec 1903 and 1924, Racine HIW-716 and the Fairmount H8508 impact wrench will provide improved hole drilling performance when used with the Aggressor carbide tipped wood auger drill. The Aggressor carbide tipped wood augers also work well in heavy-duty electric, pneumatic, and gas powered drill motors. The Aggressor carbide tipped wood auger drills
are fully reversible, and come in standard and extra wide diameters.
Diameters from 9/16” up to 4”, and in standard lengths from 12” to 48”.
The shank is a standard 7/16” or 5/8” hex,
but can be customized to fit most power tools.
Framing Wood Auger Drill
optional tip
Utility Framing
Wood Auger Bits
Carbide Tipped
for heavy moisture and chemical soaked wood
Diameters
7/16"* 1/2" * 9/16" * 5/8"
11/16" * 3/4" * 13/16"* 7/8" * 15/16 * 1" * 1-1/16"
Lengths
9-1/2" * 12" * 18" * 24 * 36 * 48 * standard.
Socket, SDS, Spline and Standard Shanks!
Carbide-tipped Railroad Tie bits
Optional Tip
Special sizes made!
For Railroad Ties and heavy timbers
Carbide-tipped Railroad Tie bits are especially designed for drilling
all types of wooden railroad ties, cross-ties, and pressure treated lumber.
These Railroad tie bits offers rapid chip evacuation due to
special fluting that provides a large chip storage area and prevents clogging.
The high quality carbide tip, available in a spear point (90°) design
will drill into the hardest of woods.
Simple put our Railroad Tie Bits are designed for drilling railroad ties.
Razor Line Runner
Ideal for drilling railroad cross ties, landscape timbers,
marine piles, and thick salt treated posts.
Features a razor sharp carbide edge on a single spiral hollow flute bit
that will cut quickly and cleanly effectively removing cutting debris. The design also prevents thermal buildup thus preventing melting of the work surface.
The RAZOR can be sharpened and completely rebuilt if necessary.
The unique point geometry and hollow flute design is self feeding without
the aid of a lead screw. The RAILROAD RAZOR makes an excellent
exit hole while keeping blowout to a minimum.
The RAILROAD RAZOR can be provided with various shank configurations,
the most common is the 1/2" Round Shank with 0, 1 or 3 flats.
This allows the drill bit to be chucked into a ½" Jacobs Chuck or larger drill.
Made from high quality American tools steel on precision CNC grinders.
A "must have" for any job that requires a through hole in a thick timber of spikes or bolts. sold in production units only.
min(250 pc)
Timber Wood Auger
30" and 40 Lengths only.
From 9/16 to 1-1/2 Diameters.
Custom Carbide Counter Sinks Custom manufactured. large hole counter bores.
any diameter or depth.
FIRE STORM WOOD AUGER
Fire Storm double spur for general purpose
medium to heavy duty use!
Sizes Available
Diameters:
* 9/16 * 11/16 * 13/16 * 15/16 * 1-1/16
Lengths
12 * 18 * 24 * 36 * 48
shanks 7/16 hex or 5/8 hex
special sizes and lengths available on request.
The FIRE STORM carbide tipped drill bits
are general purpose bits, medium to heavy-duty auger style
wood boring pole bit.
These wood drill bits are milled from a single piece
of steel creating a solid center and a truly unique flute design.
This combination enables these carbide
tipped wood drill bits to outperform and out last any ordinary
steel auger pole bits.
The FIRE STORM features a patented double spur,
carbide tip drill bit configuration and proven power-auger flute design.
These carbide tipped drill bits are designed to produce numerous
straight holes and is self-feeding The FIRE STORM works equally
well with newer hydraulic power tools that utilize a high torque,
high R. P. M. design, or with older hydraulic tools that may develop
slightly less torque and speed. FIRE STORM carbide tipped wood drill bits
can also be used with most heavy-duty electric, pneumatic, or
gasoline powered drill motors or impact wrenches rated
at 1/2" capacity or larger. Do not use reverse drilling when removing,
the FIRE STORM is NOT a reversible bit. FIRE STORM carbide tipped
wood drill bits can be completely rebuilt and repaired. "Wood Bore".
Carbide Tip Wood Core Drill
for large deep hole drilling!
2" to 24" diameters
any depths!
 
Turf Drills
For golf courses, sports stadiums, landscaping.
specially manufactured for each need.
1" capacity Reversible
price cannot be advertised, call for substantial discounts!
Model No. ADV -1903
- Ideal for drilling wood in marine timbers, underwater use and railroad repair work
- Thrust bearing support for long life and efficient operation
- Lever throttle and durable spur gearing
- Breast plate and dead handle included
- Includes threaded exhaust port
- Use underwater with Air Tool Line Conditioner
Accessories and wood boring drill bits from 1/2" dia. to 4" dia. in lengths from 12" to 124" |
|
|
|
|
| Model ADV-1903 - 1" dia. capacity in wood | | Capacity in wood: | 1" Diameter | | Reversible: | Yes | | Power: | 2 HP | | Chuck Style: | 1/2" Wood boring | | Spindle: | Stub Taper | | Free Speed: | 750 RPM | | Recommended Hose Size: | 1/2" | | Overall Height: | 17-1/2" | | Weight: | 14-1/2 lbs. | | Air Inlet Thread: | 1/2" ID | | Air Exhaust Thread : | 1/2" NPT | | Air Consumption at 90 PSI : | 39 CFM |
|
Milwaukee 3/4 chuck HD drill for timber bits.
mt3
price cannot be advertised, call for substantial discounts!
|
Sutton Tool
